DataRemote Technical Support & Knowledgebase
| ||
|
|
| |
| FAQ(s) found under Troubleshooting | Showing 21 Of 21 | Prev |
| I'm Programming a CDS-9060 with a SPRINT # and the MDN is different then the MIN. Ever time I tell it to program it defaults back to the MIN. Why is this happening and is there a fix? | |||||||||
| |||||||||
For some reason when programming some Sprint numbers that have 2 different numbers for the MIN and MDN - The Kyocera radio defaults back to the MIN number - To fix this you need to hard code it in using AT-Commands. We appolagize for the inconvenience. please follow the commands below to fix the problem..
Using AT commands: 1. AT$KWSPC=<000000> Unlocks module. <spc> is your Service Programming
Code for the module. If the Service Programming Code is correct, the module will display: SPC UNLOCKED If the Service Programming Code is incorrect, the module will display: ERROR: INCORRECT SPC 2. AT$KWMODE=1 Places module in offline mode.
Module will display: MODE CHANGED DIRECTORY NUMBER CHANGED 4. AT$KWMSID=<MSID> Writes MSID. This is displayed as the 'IMSI_M S' in
the PST. If you have successfully written the MSID, the module will display: MOBILE ID CHANGED 5. AT$KWMODE=2 Resets the module
Module will display: MODE CHANGED 6. Wait at least 20 seconds for the module to reset.
7. Verify that the MDN and MSID are correctly written to the module. By going back into the Config Menu "Programming Modem ************** PROGRAMMING MENU ************* Equipment Serial Number : 03414557330 |
| Related FAQs In This Category |
| • How do I disable flow control? |
| • Can you send SMS\Text messages using CDMA on Verizon using AT-Commands? |
| Submit Questions / Post Inquiries |
| If your question have not been answered, or if you would like to send us an inquiry, please click here |
| Most Popular Questions |
| • When is Analog Cellular going away???? Replace your Analog Cellular Data unit’s before it’s too late! ... Views : 12017 Last Update : 2007-08-08 |
| • I received "No Carrier" after dialing ATDT+Phone Number within 4 seconds, what does that mean? Check with your CDMA Provider to "make sure that your number is provisioned correctly. ... Views : 7412 Date Add : 2007-03-29 |
| • CDS-9022\9060 has 16 pin header. I need to know how to get the cryout SMS\Email alarms working, which pins are inputs and which are outputs. thank you in advance. Pin-out 9022 P7 \ 9060 P2 1 = Input 0 2 = GND 3 = Input 1 &n... Views : 7344 Last Update : 2007-03-14 |
| Latest Added FAQs |
| • I'm Programming a CDS-9060 with a SPRINT # and the MDN is different then the MIN. Ever time I tell it to program it defaults back to the MIN. Why is this happening and is there a fix? For some reason when programming some Sprint numbers that have 2 different numbers for the MIN and M... Views : 2377 Date Add : 2008-06-13 |
| • How do I test the CDS-9060-TR to make sure the internal modem and local loop is working properly? The attached file will test the RJ-11 Tip and Ring function and the internal Analog modem. &nbs... Views : 2259 Date Add : 2007-05-29 |
| • Does the CDS products have Modem Emulation mode for spoofing software? Modem Emulation mode -The CDS modems act like a Dialup\Dial-outbound standard Hayes AT-Compatib... Views : 5696 Last Update : 2007-10-13 |
Technical Support
Warranty & Return Policy
 |
|
 |
|
 |
|
 |
| Browse by Category | |
 |
Setup & Configuration (29) Setting up and configuring your DataRemote Modems |
|
Troubleshooting (21) Troubleshooting your DataRemote Modems. |
|
Tutorials (2) Tutorials for setup and configuration of your DataRemote Wireless Modems. |
|
Terminology (4) Commonly used terms associated with the Cellular Industry |