|
DataRemote Technical Support & Knowledgebase
Troubleshooting | [ All FAQ In This Category ] | | How do I know I知 talking to the correct com-port? | | I can稚 get into the Configuration Menu, what do I do? | Does the CDS products have Modem Emulation mode
for spoofing software?
| | Can I get a DataRemote Modem with a Static IP? | | How Do I Perform An Over-the-Air Activation Of The Unit? | CDS-9022\9060 has 16 pin header. I need to know how to get the cryout SMS\Email alarms working, which pins are inputs and which are outputs. thank you in advance.
| | Can you send SMS\Text messages using CDMA on Verizon using AT-Commands? | | what is the input voltage for the CDS modems ? | | I received "No Carrier" after dialing ATDT+Phone Number within 4 seconds, what does that mean? | | Do I Need A Null Modem Cable? | | How do I disable flow control? | | How do I save AT-Commands to the modems profile? | | How do you program the modem to log onto the 1XRTT \ internet using TCP or UDP? | | How can I reset my modem back to factory default? I have a CDS-9060 modem how do I do a hard reboot? Go back to default? How do I reset the modem back to default? | Can you display the Signal Strength when talking to the unit remotely?
Is there a AT-Command to display the signal strength" | | In The Alarm setup menu I can't save the Cry-Out Contact email address and mobile numbers? | What is the Pin-Out for the CDS modems DB-9?
Part# DRA-RS232
| | When is Analog Cellular going away???? | How do I type AT-Commands to the Analog modem in the CDS-9060-TR?
Is the CDS-9060-TR a Cost Effective & Rugged CDMA cell modem cell available in 1x mode and CS \ IS-95 Dial Up mode. | | How do I test the CDS-9060-TR to make sure the internal modem and local loop is working properly? | | I'm Programming a CDS-9060 with a SPRINT # and the MDN is different then the MIN. Ever time I tell it to program it defaults back to the MIN. Why is this happening and is there a fix? |
Setup & Configuration | [ All FAQ In This Category ] | | Does The Modem Require Any Special Drivers? | | How do I program my modem? | I知 using the CDS-9060 with a PLC I call into the unit from a landline modem. I want to know if the CDS-9060 Cellular modem has AT-Commands that can be used to LOG onto the internet in TCP or UDP mode "Packet Data"? I知 wanting to dial into a IP address to talk the the PLC\RTU\Remote Computer\DTE device.
Thanks in advance,
Bill Thornwhite
Control Systems
Richmond, TX
| | How do you get into the setup Menu's to program the CDS Modem? | I知 using the CDS-9060 hook via RS-232 to a PLC I call into the unit from a landline modem. I want to know if the CDS-9060 Cellular modem has AT-Commands that can be used to LOG onto the internet in TCP or UDP mode? I知 wanting to dial from a host computer into a IP address\CDS modem Communicating to a PLC\RTU .
Thanks in advance,
Bill Thornwhite
Control Systems
Richmond, TX
| Does the CDS products have Modem Emulation mode
for spoofing software?
| | How do I program the telephone number? | CDS-9022\9060 has 16 pin header. I need to know how to get the cryout SMS\Email alarms working, which pins are inputs and which are outputs. thank you in advance.
| | Can you send SMS\Text messages using CDMA on Verizon using AT-Commands? | | The Modem Does Not Answer When I Dial From Another Modem. | | How do I check signal strength? | | I received "No Carrier" after dialing ATDT+Phone Number within 4 seconds, what does that mean? | | Do I Need A Null Modem Cable? | | How do you program the modem to log onto the 1XRTT \ internet using TCP or UDP? | What is the normal baud rate of data transmission with all alternative rates
available?
| | How can I reset my modem back to factory default? I have a CDS-9060 modem how do I do a hard reboot? Go back to default? How do I reset the modem back to default? | | How do I change the Baud rate local and remotely? | | How do I put the CDS-9060 in TCP Server Mode? | | Peek ADR traffic counter how do you wire the rs-232 using a 3 or 4 wire connection | What is the Pin-Out for the CDS modems DB-9?
Part# DRA-RS232
| Can I send SMS \ Text messages using AT-Commands on your CDMA modems? if so what are the commands?
Thank you,
Bill Webzork | | When is Analog Cellular going away???? | | Configuring the DataRemote CDS-9022\9060 cellular modem to work with the GSC3000 or VRC2500 | | Quick setup for the GSM CDS-1900 - How do I activate the CDS-1900? | | How do I send SMS commands? where do I find a list of commands? Can I send to a Email address? | Adding MIP to a 9060 ALLTEL modem. Programming the MIP into a CDS-9060 on Alltel
Using AT Commands to set the MIP Parameters for ALLTEL:
| | Hi, I require a CDMA modem to run off 24VDC and be used in remote applications where a serial interface is required. Most importantly, I need the modem to be compatible with the following serial port parameters - Baud 115200, Data Bits 7, Par ity Even and 1 stop bit. Please let me know which modem will allow this. Thanks in advance. M2M text messaging using Data Bits of 7,E,1 @ 115200bps |
SETUP | [ All FAQ In This Category ] |
Tutorials | [ All FAQ In This Category ] | | When is Analog Cellular going away???? |
Terminology | [ All FAQ In This Category ] | | What is IS-95? | | What is 1XRTT ? | | What is a CNAME-Record? | | When is Analog Cellular going away???? |
|
|
|
